What Does an Electric Scooter’s Ignition Switch Do?
An electric scooter’s ignition switch is a small button or switch that is typically found close to the handlebars. It is what starts the engine and turns on the power to it. For more on our best heavy duty mobility scooters visit Everlasting Mobility.
It is made up of two components: a key cylinder and a starter motor. The scooter is started by using the cylinder to activate the starter motor.
How to Disable an Electric Scooter’s Ignition Switch in Seven Easy Steps
An electric scooter’s ignition can be easily bypassed by someone with technical knowledge. The first step is to determine the type of starting ignition you have. Either a keypad ignition or a standard push-button ignition is available for scooters. Although they are very similar, the keypad might require a real key to operate.
When attempting this, keep in mind that additional safety precautions should be followed, such as wearing insulated gloves and keeping exposed wires away from combustible materials. You should always check the owner’s handbook first because different models may have different instructions.
1. Take The Handlebars Off
Removing the handlebars is the first step in circumventing the ignition switch. All you need to do to complete this fairly straightforward task is remove any screws holding it in place. Check out our post on how to start a mobility scooter without a key for some useful tips and tricks if you’ve ever been stranded with a mobility scooter that won’t start due to a lost or broken key.
2. The Clutch Cable
Locating the clutch cable, which will be connected to the ignition switch, is the next step. Because you must understand and keep in mind how these components are organized, this might be tricky. If you can, take a photo of the original wiring and save it for reference.
Bypassing the switch and connecting the clutch cable directly to the starting relay motor will be accomplished using the jumper wire. The green wires must be attached to one side of the jumper wire as they represent the positive end of the starter relay motor. The black wire must be attached to the other side of the wire because it is the motor’s negative end.
Before you begin, make sure you comprehend every wire. Even combining two wires incorrectly can have unfavorable effects.
3. Battery Is Disconnected
Make sure the battery has been disconnected in order to be safe. This will reduce the chance of electric shocks and prevent component damage. The power should be turned off from the mains and the kill switch should be in the off position.
4. Remove the Cover Plate
It’s time to remove the cover plate when the battery has been unplugged. This is typically a plastic panel that may be removed and covers the entire ignition switch. Are you trying to figure out where the speed limitation is on your mobility scooter? You may get the knowledge you need to operate your scooter safely and efficiently by reading our article on the subject.
5. Remove the Ignition Switch Screw
Finally, you can disassemble the ignition switch by unscrewing it. As soon as you have the cover plate off, the procedure is typically straightforward.
6. Connect The Wires
The ignition switch can be hotwired or changed for a new one once it has been removed. Use electrical tape or wire nuts to join the wires that were previously attached to the switch in order to bypass the ignition switch.
Make sure the scooter is operating smoothly by turning on the electricity. To keep the connections together and prevent them from coming undone, use wire nuts or electrical tape. If you prefer to replace the switch, it is typically a straightforward task that just requires a few basic tools and a new ignition switch. Always check that the replacement switch is appropriate for your scooter and that the cables it comes with are compatible with the ones already in place.
7. Put Everything Back Together
Place everything back and reconnect the batteries after the wires have been linked or a new ignition switch has been installed. Now that it is ready to use, your electric scooter should be. Verify that the engine starts accurately and that no error or warning lights are on. You can now resume enjoying your electric scooter if everything appears to be in order.
Would you like to donate a mobility scooter to someone in need if you no longer need it? You can find organizations that accept contributions and who can help you make a difference in someone’s life by consulting our post on where to donate a mobility scooter nearby.
Everlasting Mobility is the number one online seller for all terrain power wheelchairs. With excellent customer support, no sales tax, FREE Shipping and financing, we offer the best in web pricing.
 "sell gold Melbourne")
